|
|
|
|
Pilt on illustreeriv
|
ProfiBus OLM/G12 V4.0 Optical Link Module, 1 RS485, 2 glass FOC interfaces (4 BFOC sockets), up to 2850m, signaling contact, measuring output Kood:
6GK1503-3CB00
Hind (indikatiivne)
Tootja
:
|
Saadavus:
14 päeva
|
Kaal:
0.4358 kg/tk
|
Maht:
0.0013 m3/tk
|
|
|
|
|
ProfiBus OLM/G12 V4.0 Optical Link Module, 1 RS485 ˄2 glass FOC interfaces (4 BFOC sockets), up to 2850m, signaling contact ˄measuring output, SiemensSIMATIC DP, interface DP/PA-Link and ET200M IM153-2 HF for extended temperature range for max. 12 S7-300 modules with redundancy capability, Timestamping suitable for isochronous mode New features: up to 12 modules can be used Slave Initiative for Drive ES and Switch ES Expanded quantity structure for HART auxiliary variables Operation of the 64-channel modules 32 signals / slot +++ Observe compatibility instructions in manual +++
| General information |
| Product type designation |
IM 153-2 HF |
| Firmware version |
V6.0.0 |
| Vendor identification (VendorID) |
801Eh |
| Supply voltage |
| Rated value (DC) |
|
| ● 24 V DC |
Yes |
| permissible range, lower limit (DC) |
20.4 V |
| permissible range, upper limit (DC) |
28.8 V |
| external protection for power supply lines (recommendation) |
2,5 A |
| Mains buffering |
| ● Mains/voltage failure stored energy time |
5 ms |
| Input current |
| Current consumption, max. |
650 mA |
| Inrush current, typ. |
3 A |
| I²t |
0.1 A²·s |
| Output current |
| for backplane bus (5 V DC), max. |
1.5 A |
| Power loss |
| Power loss, typ. |
5.5 W |
| Address area |
| Addressing volume |
| ● Inputs |
244 byte |
| ● Outputs |
244 byte |
| Hardware configuration |
| Number of modules per DP slave interface, max. |
12 |
| Time stamping |
| Accuracy |
1 ms; 1ms at up to 8 modules; 10ms at up to 12 modules |
| Number of message buffers |
15 |
| Messages per message buffer |
20 |
| Number of stampable digital inputs, max. |
128; Max. 128 signals/station; max. 32 signals/slot |
| Time format |
RFC 1119 |
| Time resolution |
0.466 ns |
| Time interval for transmitting the message buffer if a message is present |
1 000 ms |
| Time stamp on signal change |
rising / falling edge as signal entering or exiting |
| Interfaces |
| Transmission procedure |
RS 485 |
| PROFIBUS DP |
| ● Node addresses |
1 to 125 permitted |
| ● automatic detection of transmission rate |
Yes |
| ● Output current, max. |
70 mA |
| ● Transmission rate, max. |
12 Mbit/s |
| ● SYNC capability |
Yes |
| ● FREEZE capability |
Yes |
| ● Direct data exchange (slave-to-slave communication) |
Yes; as publisher with all IO, as subscriber with F-IO only |
| ● Design of electrical connection of PROFIBUS interface |
9-pin sub D |
| 1. Interface |
| PROFIBUS DP slave |
| ● GSD file |
SI05801E.GSG |
| ● automatic baud rate search |
Yes |
| Protocols |
| Bus protocol/transmission protocol |
PROFIBUS DP to EN 50170 |
| Potential separation |
| Potential separation exists |
Yes |
| Isolation |
| Isolation tested with |
Isolation voltage 500 V |
| Degree and class of protection |
| IP degree of protection |
IP20 |
| Ambient conditions |
| Altitude during operation relating to sea level |
| ● Installation altitude above sea level, max. |
3 000 m |
| Configuration |
| Configuration software |
| ● STEP 7 |
Yes; STEP 7 / COM PROFIBUS / non-Siemens tools via GSD file |
| Dimensions |
| Width |
40 mm |
| Height |
125 mm |
| Depth |
117 mm |
| Weights |
| Weight, approx. |
360 g |
| last modified: |
11/10/2018 |
|
|
File description
|
File type
|
Download link
|
|
|
|
|
|
|
|
|
|
